Hey everyone, let’s cut to the chase—if you’re in the industrial game, you’ve definitely been there: you’re updating a line, fixing a leak, or reconfiguring a run, and you’re staring at a plastic tube that’s glued, crimped, or pressed way too tight into a metal or plastic fitting. Pulling it out wrong can snap the tube, crack the fitting, or leave bits of plastic stuck that cause headaches later. As a plastic tubes supplier that works with folks across plumbing, automotive, and manufacturing, I’ve seen every bad move (and fixed most of them) over the years. Today I’m walking through exactly how to do this safely, so you don’t waste time, money, or tubes. Plastic Tubes

First off, let’s get one thing straight: not all fittings are the same, and not all plastic tubes are either. That’s why your go-to trick for a ½-inch PVC tube in a compression fitting is totally different than a ⅛-inch nylon tube in a pneumatic push-to-connect. I’ve had customers reach out panicking because they tried to yank a tube out of a barbed fitting and it snapped right off—don’t be that guy. Let’s start with pre-checks, because skipping these is where most mistakes happen.
Before you even touch a tool, turn off the supply. Whether it’s air, water, or hydraulic fluid, you don’t want to get sprayed with pressurized gunk mid-removal. Then, give the tube and fitting a quick once-over. Push-to-connect fittings are the easiest, honestly—they’re made to let you remove tubes, no glue or crimp. Most of these have a little release collar, right? You just squeeze that collar tight as you can (I use a small pair of needle-nose pliers if my fingers are too big) and pull the tube straight out. Wait—don’t wiggle it back and forth. Wiggling can bend the tube inside the fitting, make it catch, or even damage the O-ring inside the fitting, which means you’ll have to replace the whole thing after. If that collar’s stuck, a quick spritz of WD-40 or some soapy water around the collar usually loosens it up. I always tell new customers: test it on a scrap tube first if you have one. It takes 2 seconds and saves you from ruining a good tube.
Next up: compression fittings. These are super common for PVC, PE, or nylon tubes, and they have a nut, a ferrule, and a body. A lot of people think the nut is holding the tube in—but no, the ferrule is the actual thing crimped onto the tube. To remove it, you first loosen the compression nut with a wrench (don’t overdo it, just enough so it spins free). Then, grab the tube near the end, close to the fitting, and pull. If it won’t budge, you can gently twist the tube back and forth a quarter turn each way—no more than that, because twisting too much can kink the tube. If it’s still stuck, don’t get a drill or knife yet. A little heat can work here, but only if your tube is heat-resistant (like PVC, not something super thin or heat-sensitive like LDPE). Use a heat gun on low, hold it 2-3 inches away from the end of the fitting for 10-15 seconds, then try pulling. The heat softens the ferrule just a tiny bit, so it slides off easier. Just don’t melt the tube—you’ll know if it’s melting, it’ll get glossy and oozing. If all else fails, cut the tube off 1 inch back from the fitting, then use a small screwdriver to pry the remaining bit of tube out from the inside. I keep a cheap pick set in my toolbox just for this, way better than a screwdriver because it’s thinner and doesn’t scratch the fitting.
Now the trickiest ones: barbed fittings. These have those little ridges inside that bite into the tube to hold it in place. This is where most people snap tubes. If you just yank it, the tube will split right where the barb is. First, cut the tube as close to the fitting as you can—don’t leave a long piece sticking out. Then, use a utility knife to make a tiny longitudinal cut along the side of the remaining tube bit, right between two barbs. Don’t cut too deep, you just want to score it, not slice through. Then, you can gently peel the sides of the cut tube away from the barbs. If it’s still stuck, a little heat (again, low heat) on the cut ends will soften the plastic so it bends easier. Another trick I’ve learned over the years: a small amount of lubricant around the outside of the fitting. Not too much, just a drop of soapy water or silicone spray. It doesn’t get between the tube and the barb enough to ruin the connection if you put it back, but it reduces friction so you can pull it out. I’ve had so many customers say this works when nothing else does—way better than brute force.
Wait, what about when the tube broke off inside the fitting? That’s a common mess. Don’t stick a screwdriver in there and jam it—you’ll just push the broken tube deeper and make it harder to get. Instead, get a pair of small pliers (needle-nose is best) and twist the broken tube bit gently back and forth as you pull. If the tube is soft plastic like nylon, you can also heat the broken end a little with a match (careful, don’t burn the fitting) to make the end a tiny bit soft, then pinch it with pliers and pull. If that still doesn’t work, I’ve used a small drill bit—just the right size to fit inside the broken tube—drill a tiny hole in the end, then push a paper clip or small nail into the hole. Then you can yank the nail/ paper clip and the broken tube comes with it. It’s a trick I picked up from a mechanic friend, works like a charm.
Now, a few do’s and don’ts I’ve learned from mistakes (and customer mistakes) over the years. Do use the right tool for the job. Don’t use a big wrench on a tiny fitting, it’ll crack the fitting. Don’t use a knife to pry at the tube inside the fitting—you’ll nick the fitting and get leaks later. Do lubricate, don’t force. I’ve seen people spend 20 minutes trying to yank a tube out, when a spritz of soapy water would have done it in 10 seconds. Do test the fitting after you get the tube out. Check for burrs, check if the O-ring (if it has one) is intact. If it looks worn, replace it before you put a new tube in. A lot of people skip that and end up with a leak a week later.
As a plastic tubes supplier, I can’t stress enough that using the right tube for the fitting matters too. If you’re using a tube that’s too thin, or the wrong material, it’s way more likely to snap or get stuck. For example, if you have a barbed fitting, make sure your tube has a smooth outer surface (not corrugated) that can slide over the barbs easily. For compression fittings, the tube’s outer diameter has to match the fitting’s exactly—too big and the ferrule won’t squeeze, too small and it’ll leak. I always tell customers to double-check that when they’re ordering.
If you’re working on a big project, say reconfiguring a whole line, and you’re going to be removing a lot of tubes, it’s worth grabbing a cheap tube puller. They’re not expensive, and they’re designed to fit right around the tube, so you get even pressure instead of just pulling from one side, which reduces breakage. I keep a few in stock in my warehouse, and I recommend them to regular customers who do this all the time.

And hey, if you’re still stuck? Don’t guess. Send a pic of the fitting and tube to our team, and we can walk you through it. We’ve got people who’ve been in the game for 10+ years, they’ve seen every type of fitting and tube out there, so they can give you exact steps for your specific setup. We work with all kinds of tubes—PVC, PE, nylon, PEX, you name it—and we know all the little tricks that make removal easy.
Glass Bottles At the end of the day, removing plastic tubes from fittings doesn’t have to be a nightmare. It’s all about knowing what type of fitting you’re dealing with, taking your time, and not forcing it. Skip the brute force, use the right tools, and a little lube goes a long way. If you’re working on a project and need new tubes, or you’re not sure which type will work best for your fittings, hit us up for a chat. We don’t just supply plastic tubes—we help folks get the job done right, no extra hassle. No weird hoops, no endless forms, just straight answers and good products.
References
- Plastic Pipe and Fittings Association. (2020). Installation and Maintenance Guidelines for Thermoplastic Tubing in Industrial Applications.
- Pneumatic Systems Design Handbook. (2021). Push-to-Connect Fitting Removal and Troubleshooting.
- ASTM International. (2019). Standard Practice for Determining Compatibility of Tubing and Fittings in Fluid Power Systems.
- Industrial Maintenance and Plant Operations Magazine. (2022). Common Mistakes When Removing Tubing From Barbed and Compression Fittings.
- Plastics Industry Association. (2021). Heat-Assisted Removal of Thermoplastic Tubing for Repair and Reconfiguration.
Qingdao KST Packaging Co., Ltd.
We are one of the most experienced plastic tubes manufacturers and suppliers in China, also support customized service. Please feel free to wholesale bulk durable plastic tubes in stock here from our factory. Quality products and reasonable price are available.
Address: 20-203, Xiyuan, Coral Bay, Huaguan Road, High-tech Zone, Qingdao, China
E-mail: kst@kstpackaging.com
WebSite: https://www.kstpackaging.com/