If you’re running a construction site, a landscaping crew, or even a mining operation, your excavator is basically your workhorse—no it doesn’t moo or neigh, but it sure does carry more weight and get way more done on a daily basis. Over the years, I’ve talked to hundreds of operators and business owners who either overcomplicate maintaining their excavator or straight up skip routine checks to save a few bucks. Spoiler: that “small” skipped oil change or loose track bolt usually leads to a breakdown that costs 10x more in repairs, downtime, and missed project deadlines. As an excavator supplier, I see this mess all the time—so let’s cut the jargon and get real about how to keep your machine running strong, no fancy engineering degree required. Excavator

First up, let’s start with the daily pre-shift check that takes 10 minutes max, not 2 hours. I know when you’re rushing to get to a job before the rain hits, it’s tempting to hop in the cab and fire it up. But here’s the thing: that 10 minutes of checks could add 500 hours to your excavator’s lifespan. We’ve had customers bring in machines that are 15 years old and still running like they’re 5 because they never skipped this step. What do you actually check here? Outside, walk around the entire machine first. Look at the tracks—are there any missing or bent pads? Any signs of a track trying to slip off mid-job? Don’t forget to check the track tension too: a good rule of thumb is you should be able to press your thumb into the middle of the track about an inch. Too tight, and you’ll burn out the sprockets; too loose, and the track comes flying off while you’re digging a 10-foot trench. Next, check all the fluid levels—oil, hydraulic fluid, coolant, fuel. You don’t need a dipstick miracle here, just make sure they’re between the minimum and maximum lines on the tanks. Pro tip: hydraulic fluid leaks are way more common than you think, so run your hand along the hoses to feel for wet spots. Even a tiny drip can turn into a huge issue if you ignore it. Inside the cab, check the emergency stop button, the seatbelt, and all the warning lights. If a light pops on on startup, don’t just reset it—jot that down and look into it later. Those lights are your machine’s way of sending a text, and if you ignore it, the text turns into a 3 AM phone call from a repair guy.
Now, the weekly or every 50-hour check. This is where you dive a little deeper than the daily walkaround. Routine fluid and filter changes fall here, and I can’t stress enough: use the right fluids for your machine. A lot of guys will grab whatever oil is cheap at the local auto parts store, but excavators run on way more specific stuff. For example, cold climates need a different hydraulic fluid than hot deserts—use the wrong one, and your cylinders won’t extend or retract fast enough, or you’ll get sludge buildup that clogs lines. Filters too: engine oil filters, hydraulic filters, fuel filters, air filters. You should be changing these every 50 hours, or sooner if you’re working in dusty construction sites or muddy job sites. Dusty environments are a big one—if you’re digging around a lot of dry dirt, your air filter will get clogged way faster than the manual says. How do you know if it’s time to change it? Take a look through the filter; if you can’t see light through it, swap it out. Clogged air filters make your engine work harder, burn more fuel, and wear out parts way sooner. Another weekly check: the undercarriage components. That includes the rollers, idlers, sprockets, and bolts. Tighten any loose bolts here—loose bolts mean parts are vibrating and wearing out faster. If a roller is making a grinding noise, don’t wait until it seizes up and breaks. Catch it early, and a $10 part costs way less than a $1,000 repair later. Also, check the bucket teeth. Those little guys take a beating on rock, concrete, and compacted dirt. Worn teeth make you work harder, use more fuel, and can damage the bucket or even the arm. Replace them when they’re worn down to about half their size—don’t wait until they’re so gone you’re dragging the bucket on the ground, that’s a quick way to ruin the edge.
Then there’s the monthly or every 250-hour service, which is where you pull out the big guns (not really, just a few tools). This is when you do a more thorough inspection of the engine’s internal parts, the hydraulic system’s seals, and the electrical connections. Let’s start with the cooling system—flush it every 2 years or 1,000 hours, whichever comes first. Old coolant gets rusty, sludgy, and can clog the radiator fins so no air can flow through, making your engine overheat on a hot day. Overheating is one of the top causes of engine damage, and it’s totally preventable. Also, check the radiator fins themselves—use a compressed air can to blow out any dirt, bugs, or debris that’s stuck between them. I’ve seen radiators so blocked that the engine temp spiked 20 degrees in 20 minutes, all because no one took 5 minutes to clean the fins. Next, the hydraulic system seals. Hydraulic hoses and seals wear out over time, especially if you’re working in harsh conditions. Look for any cracks, bulges, or leaks on the hoses—if a hose is bulging, replace it immediately. A burst hydraulic hose can spray fluid with enough force to cut through skin, so safety first here. Also, grease all the pivot points—this is a step people so often skip, and it’s a huge mistake. Pivots on the arm, the bucket, the boom, and the blade (if you have one) all need grease to reduce friction. The manual will tell you how often, but a good rule is to grease them every 10 hours of operation. Use the right grease too—most excavators use lithium-based grease, but if you’re working in extreme cold, there’s special cold-temperature grease that won’t get hard and won’t lubricate properly. Over-greasing is a thing too—don’t pump so much that old grease pushes out and traps dirt, that’s a quick way to get dirt in the pivot and cause wear.
Wait, let’s talk about storage for a second. A lot of people keep their excavator on the job site when it’s not in use, especially if they’re working a long project. But if you’re storing it for more than a week, even if it’s not in use, there are a few things to do. First, park it on a flat, dry spot, not in a muddy low spot where water can seep into the tracks or under the engine. Cover the cab and the major parts with a breathable tarp—don’t use plastic, because plastic traps moisture and causes rust. If you’re storing it for a month or more, you should do a few extra things: fill up the fuel tank to prevent condensation (condensation in the fuel tank is a big cause of water in fuel lines), change the engine oil and filter because old oil can have acids that damage parts, and disconnect the battery to keep it from dying. Even if you’re not using the excavator, the battery will drain over time, so disconnecting it takes 2 minutes and saves you from buying a new $200 battery every few months.
Now, let’s get real about common mistakes I see all the time. First, “I’ll fix it later” attitude. Every small issue that you put off turns into a big one. A loose track bolt: put it off for a week, and the track comes off halfway through a dig, which takes 2 people and a few hours to fix, and delays your job. A tiny hydraulic leak: put it off, and the hose bursts, costing $500 for parts and $300 for labor, plus more downtime. Second, using cheap parts. I get it, everyone wants to save money, but using knockoff filters or used tracks that aren’t the right size will cost you way more in the long run. As an excavator supplier, we see guys buy a $20 oil filter instead of the $40 OEM one, and 100 hours later the engine has sludge buildup because the cheap filter didn’t do its job. It’s a false economy. Third, ignoring the operator’s manual. I know, those manuals are thick and full of boring info, but they’re written specifically for your machine. Every excavator model is a little different—some need track tension checked every 100 hours, some every 50. Some need a specific type of hydraulic fluid. Don’t go by what your neighbor’s excavator uses, go by what your manual says.

And hey, if you’re new to owning an excavator, or if you’re not sure how to do a certain check or repair, don’t hesitate to reach out. As an excavator supplier, we don’t just sell machines and vanish—we’re here to help with maintenance tips, part replacements, and even referrals to trusted mechanics if you don’t want to do it yourself. Whether you’re running a small business with one excavator or a big construction company with a fleet, keeping your machine well-maintained means less downtime, lower repair costs, and getting the job done on time, every time. If you’re looking for a reliable excavator that’s built to handle tough job sites, or you need OEM parts, or you want to talk through a maintenance plan that works for your operation, get in touch with our team to set up a time to chat and answer all your questions.
Lawn Mover References
- Construction Equipment Association. (2022). Routine Maintenance Guidelines for Compact and Heavy Excavators.
- Caterpillar Inc. (2021). Excavator Operator’s Handbook: Preventive Maintenance Best Practices.
- National Association of Construction Contractors. (2023). Cost Analysis of Excavator Downtime vs. Preventive Maintenance.
Shandong Ocean Import & Export Co., Ltd.
Shandong Ocean Import & Export Co., Ltd. is well-known as one of the leading excavator manufacturers and suppliers in China. Please feel free to buy customized excavator at competitive price from our factory. For pricelist and quotation, contact us now.
Address: Ocean Industry Area, East Outer Ring, Jining High-Tech Zone, Shandong Province, China
E-mail: info@oceanmach.com
WebSite: https://www.sdocmachine.com/